View previous topic :: View next topic |
Author |
Message |
Bandit Bill
Joined: 31 Jan 2005 Posts: 202 Location: Hamilton, Ontario, Canada
|
Posted: Tue Feb 08, 2005 1:56 am Post subject: Leading Link designs |
|
|
This isn't really an HPS question, as LL front ends are considered somewhat marginal in the handling dept. as compared to more HPS oriented center hub steering setups - but i imagine we've got a reasonable pool of experience here to lend some advice on the design of such a front end.
While i await my Charnwood motors car tire rim, i've been wracking my brain on my final leading link setup. As it sits right now, i'd settled on a custom fabricated bearing block utilising a needle roller bearing of 27 mm OD, 20 mm ID, and a 26 mm width, with an inner spacer of 30 mm width, sleeving it down to a 12 mm shouldered bolt. This is the same bearing as used on the rear wishbone suspension mount to the motorcycle frame on the Suzuki Bandit - My rational at the time of choosing it was that if it is up to the task of suspending the rear end of the bike, two of them utilised as the swinging arm pivot bearings should be up to the task of holding the front end up. I've noted also, that most commercial front ends seem to have the pivot bearing on the ends of the downtubes, with the pivot bracket mounted to the swingarm - in my case, i'm doing the opposite to this, one of the reasons being that the downtubes are going to be 44 mm in diameter, and if i mounted the pivot bearing i intend to use, the fork tubes are going to run into an interference issue with the pivot brackets.
Am i on the right track for my choice of suspension, or am i travelling down a hazardous path?
comments, alternative suggestions? _________________ Homebrew '99 Suzuki Bandit 1200 / '88 Hannigan Comet
'78 Honda CT70 playbike
http://www.chairintheair.ca |
|
Back to top |
|
|
zentime
Joined: 22 Jan 2005 Posts: 837 Location: Massachusetts USA
|
Posted: Tue Feb 08, 2005 3:46 am Post subject: |
|
|
It doesn't seem like there would be any inherent reason why the bearing couldn't be mounted to the swingarm instead of the forks. I wonder if you're going to build in any means to adjust the trail? In that case it seems like it would be better to mount the bearings to the fork. One time I built a LL using 1/2" rod ends screwed into plugs that I welded into the fork tubes. An unacceptable amount of play developed pretty quickly in the rod ends so I removed the spherical ball bushings and replaced them with standard bushings. Not sure if any of this helps but that's my input.
Bill _________________ CBR1100XX/EZS
1973 MotoGuzzi V7sport
will August ever come............ |
|
Back to top |
|
|
Bandit Bill
Joined: 31 Jan 2005 Posts: 202 Location: Hamilton, Ontario, Canada
|
Posted: Tue Feb 08, 2005 3:59 am Post subject: |
|
|
zentime wrote: | It doesn't seem like there would be any inherent reason why the bearing couldn't be mounted to the swingarm instead of the forks. I wonder if you're going to build in any means to adjust the trail? In that case it seems like it would be better to mount the bearings to the fork. One time I built a LL using 1/2" rod ends screwed into plugs that I welded into the fork tubes. An unacceptable amount of play developed pretty quickly in the rod ends so I removed the spherical ball bushings and replaced them with standard bushings. Not sure if any of this helps but that's my input.
Bill |
I considered Rod ends - but then i've seen just how sloppy the hiem joint on the end of my steering dampner has gotten in a single season of usage - and that wrote off rod ends as an option. As i envision it, the custom fabbed bearing block i'm considering, would be the adjustment method, basically in an adjustment range of 1 - 1 1/2" total fore and aft, using a slotted base that is bolted to the swinging arm. See the below picture of Robert Graur's rendition of this, which had sparked my decision to further refine the design. I'm using needle bearings on the advice of my machinist, who has said (in theory, anyway) that solid delrin type bearings tend to wear oval with heavier loads placed on them, and are more difficult to remove and replace cleanly out of aluminum. I'd also have to make the shock mounts range adjustable, using this method, but the shocks i'm using are length variable to compensate.
_________________ Homebrew '99 Suzuki Bandit 1200 / '88 Hannigan Comet
'78 Honda CT70 playbike
http://www.chairintheair.ca |
|
Back to top |
|
|
zentime
Joined: 22 Jan 2005 Posts: 837 Location: Massachusetts USA
|
Posted: Tue Feb 08, 2005 4:06 am Post subject: |
|
|
Seems like a nice design to me. Great way to adjust the trail. Clean and simple.
Bill _________________ CBR1100XX/EZS
1973 MotoGuzzi V7sport
will August ever come............ |
|
Back to top |
|
|
swaybar2002
Joined: 26 Jan 2005 Posts: 380 Location: Central Pa.
|
Posted: Tue Feb 08, 2005 5:17 am Post subject: |
|
|
Bill,
As I had mentioned when you first shared that pic a while back it certainly looks liek a nice desigh. The adjustable trail is a very nice feature too.
I am curiou sif you have settled on mounting the calipers direct to the swingarm or creating a floating caliper design. ('floating' in this case meanintg the caliper would be secured by a link and a 'pivot' at the fron axle.) _________________ Claude Stanley
Founder: Internet Sidecar Owners Klub
http://autos.groups.yahoo.com/group/SCT/
2007
I.S.O.K Sidecar RON-DEE-VOO III ..
First full weekend in August!! Thursday through Sunday!!
Weikert, Pa ..more details coming |
|
Back to top |
|
|
Bandit Bill
Joined: 31 Jan 2005 Posts: 202 Location: Hamilton, Ontario, Canada
|
Posted: Tue Feb 08, 2005 5:27 am Post subject: |
|
|
swaybar2002 wrote: | Bill,
As I had mentioned when you first shared that pic a while back it certainly looks liek a nice desigh. The adjustable trail is a very nice feature too.
I am curiou sif you have settled on mounting the calipers direct to the swingarm or creating a floating caliper design. ('floating' in this case meanintg the caliper would be secured by a link and a 'pivot' at the fron axle.) |
Definitely floating, with the bracket being attached to the axle spacers, and tied off of the down tubes via adjustable hiem joints. To mount the calipers direct to the swinging arm introduces undesirable braking lift of the swinging arm.. If i'm going to all this bother to construct a LL .. i might as well take this 1 step further and do it right _________________ Homebrew '99 Suzuki Bandit 1200 / '88 Hannigan Comet
'78 Honda CT70 playbike
http://www.chairintheair.ca |
|
Back to top |
|
|
swaybar2002
Joined: 26 Jan 2005 Posts: 380 Location: Central Pa.
|
Posted: Tue Feb 08, 2005 5:36 am Post subject: |
|
|
Sounds good Bill! _________________ Claude Stanley
Founder: Internet Sidecar Owners Klub
http://autos.groups.yahoo.com/group/SCT/
2007
I.S.O.K Sidecar RON-DEE-VOO III ..
First full weekend in August!! Thursday through Sunday!!
Weikert, Pa ..more details coming |
|
Back to top |
|
|
bmcsheehy
Joined: 22 Jan 2005 Posts: 991 Location: Massachusetts USA
|
Posted: Wed Feb 09, 2005 6:27 pm Post subject: |
|
|
Bill Strong,
Just re reading some post here. Who does you fabrication work, they did a nice job. Really looks neat and clean. _________________ Bill
High Performance Sidecaring... ...There is nothing "HACKED" about it.
2006 ZX-14 / HANNIGAN HP.
2011 Concourse / California Friendship III.
2016 Suzuki Bandit 1250s
1936 Ford Fordoor Humpback
www.Yankee-Engineering.com |
|
Back to top |
|
|
Bandit Bill
Joined: 31 Jan 2005 Posts: 202 Location: Hamilton, Ontario, Canada
|
Posted: Wed Feb 09, 2005 7:24 pm Post subject: |
|
|
Hi Bill
The photo I put up in the proceeding post of the swinging arm/bearing block assembly is NOT of my work - it is of Robert Graur's custom BMW/sidecar rig he's put together. I've simply decided to borrow his design and adapt to my own setup. The machine shop that i lean on to do what i cannot, does do similar quality work - for the right cash / no receipt price, however.
http://www.canadianbron.ca/ _________________ Homebrew '99 Suzuki Bandit 1200 / '88 Hannigan Comet
'78 Honda CT70 playbike
http://www.chairintheair.ca |
|
Back to top |
|
|
|